-
ABTEC爱普泰科 高性能电声测试测试仪 多通道音频测试仪 A4
¥6.90万
-
ABTEC爱普泰科 2通道音频分析仪 音频综合测试仪 A2
¥5.30万
-
ABTEC 爱普泰科 音频分析仪 音频综合测试仪 A1DD
¥4.30万
-
AMETEK Asterion 交流电源 大功率交流源
¥4.10万
-
AMETEK 阿美特克 高稳定度可编程直流电源 ASD
¥3.20万
- 产品参数
- 图文介绍
- 企业简介
- 企业地址
J2120A Line Injector
1、 10Hz~10MHz可用的频宽
2、 低损失(Insertion loss)设计
3、 5安培的zui大电流
4、 50Vdczui大的输入
5、 可轻易测量电源输入滤波器(Input filter)和PSRR
6、 详细规格
產品说明
While the injection transformer is a very wideband adapter, it is not useful for measuring ripple rejection (PSRR) of a power supply or even an opamp. This is because the attributes that make the injection transformer perform so well also result in a transformer that is intolerant of DC current. Even very small DC currents (5mA or less) can greatly reduce the signal capacity or even totally saturate the transformer. For this reason, the Picotest line injector (J2120A) is another essential test adapter.
The line injector allows the input DC supply voltage to be modulated by the network analyzer source signal, as in the case of a PSRR measurement. The line injector must be capable of a frequency range well below the AC line frequency and at least above the control loop bandwidth of the circuit being tested.
The line injector is only capable of sourcing current, so that the output amplitude can be significantly impacted by the operating current and the total storage capacitance at the load. The network analyzer has a very high selectivity so distortion at the output of the line injector generally does not influence the measurement. Again, this is a small signal injector, so the oscillator signals should be kept as small as possible above the noise floor. As a guide, try to keep the input signal amplitude below 50mVpp (-20dBm). In some cases we want to attenuate the source signal even further, and so we have included the attenuators in the injector kits. Some analyzers, such as the Omicron-Lab-Lab Bode-100 allow shaping the injection amplitude as a function of frequency, which helps optimize the signal level.
Measuring Output Impedance
The line injector can also be used in conjunction with a current probe to measure the input impedance of a power supply. The input impedance of a switching power supply or regulator is negative, which is a stability concern when combined with an EMI filter, making the measurement an important part of the design, analysis and verification process. The current probe must be set for 1A/V or the results need to be scaled accordingly for different settings.
-
PICOTEST 3.4英寸多功能数字万用表 M3520A¥6300.00
-
Keysight 在线测试仪 ITC自动测试线 I3070¥170.00万
-
Keysight ICT在线测试设备仪 ITC自动测试线 I3070¥170.00万
-
Agilent 微波信号源 信号源租赁维修 E8257D¥1.40万
-
Agilent/安捷伦 频谱分析仪租赁维修 N9320A¥4300.00
-
AMETEK 阿美特克 高性能直流电源 可编程模块化水冷直流电源 高稳定度可编程直流电源 ASD
¥3.20万
-
AMETEK 阿美特克程控电源 大功率可编程交流电源 BPS
¥5.10万
-
AMETEK 阿美特克程控电源 交流电源 Asterion
¥4.10万
-
PICOTEST 光耦合件测试 CTR万用表 M3522A
¥6300.00
-
PICOTEST 多功能数字万用表 M3521A
¥6300.00
- 产品参数
- 图文介绍
- 企业简介
- 企业地址